dimplewillow6

Reasons to Change Door Lock There are many reasons to replace your door lock, from upgrading your home's security to re-decorating your entryway. You might also have to change locks if the key gets stuck inside or is difficult to turn. DIY novices can also change their locks. Gather the materials needed to begin. Take off the lock that was previously used. Before installing a new lock it is important to take out the old lock from the door. This is especially crucial in the event that you suspect someone else has access to your home. It's also a good idea after you've moved into a new home, experienced a burglary, or welcomed a roommate. The process is a lot simpler than you think and can be completed within just a few minutes. Begin by removing the screws that hold the deadbolt faceplate to the frame of the door. To remove the faceplate, you'll need to remove screws on both sides. This will let you discover what's behind it and give you a better understanding of what to do with the remaining steps. After you have removed the old faceplate, you'll need to remove the bolt and strike plate. Use a screwdriver or a wrench to loosen the bolt and then remove it from the hole in the door. If the bolt is rusted, you may have to use a chisel and hit it. When using a chisel remove the bolt, take care to not to damage the door frame. Make sure the new deadbolt, doorknob and lock will fit into the holes already in the door before you remove the old one. Many hardware stores and large box stores carry a variety of locks and will assist you in choosing the right one. Ask for help if the lock you purchased does not fit your door. When you're removing the old lock, look for small depressions or notches in the handle or around the trim. If you can find them, slip a straightened safety pin or a flat screwdriver through them to loosen the handle and expose screws underneath. After the screw in the handle is removed, you can begin to remove the knob from its spindle. To do this, locate the set screw at the base of knob and loosen. Next, you will need to remove the knob from the spindle and carefully remove the spindle from the door. Install the new lock It's a good idea to change locks on doors throughout your home regularly, especially after a burglary or when you move into a new home with roommates. It's an affordable, simple and efficient way to ensure that your home is secure. The majority of people can do this themselves with a screwdriver and some basic instructions. You may also wish to learn how to rekey your door lock to ensure that only you have the key. To begin the process, you must purchase a new lock that matches the keyway on your existing lock. Many locksmiths will change the lock's key for a fee but you can save money by doing this yourself. You can buy a new lock from an hardware store, or on the internet. A standard deadbolt should fit on most doors however, you'll need to measure the size of your door to make sure that it fits. Most of the time, your new lock will be supplied with an image of a cardboard model that shows the way it will fit on the door. The template can be used to drill the hole. It is much easier than having to measure every time. If the template does not line up with your hole, you should take it back to the hardware store to purchase another one. The new lock on the right-hand side of the door. You can check this by looking at the latch, which must be labeled “up” or something similar. Make sure the latch is seated correctly in the plate and attach it using the supplied screws. If you're replacing the knob lock on your door, it's also important to be aware of the type of lock you're using. Certain knob locks are left-handed. If you are not careful, the lock could be placed on the wrong side of your door, which could prevent it from being locked from the outside or inside. It is recommended to test the new lock after you finish. You should be able to lock the door from both the inside as well as the outside, and unlock it with a key. If you are not satisfied with the outcome, you can call an expert locksmith to repair it. Test the lock A door lock that won't unlock can be a nuisance and can be dangerous, it could also put your family's safety at risk. It's simple to solve the majority of door lock issues by performing some troubleshooting, and lubrication. Verify that the key has been properly cut, and that the lock assembly isn't dirty or loose. If this doesn't fix the issue, try applying lubrication to the door lock actuator using powdered graphite or a silicone-based grease. Check that the door lock switch, wiring harnesses and actuator connector are all working correctly. To check this, consult the manual or wiring diagram to determine the purpose and color-coding of all door lock switch wires. Then, test the wires using a light or digital meter to see if the door lock actuator receives power and ground when the switches are activated. If you notice voltage switches that toggle with each other it means that the switches are in good working order and the actuator is likely to need replacing. If the switch appears to work but the actuator does not move when you turn it, there may be a problem in the cylinder. The actuator cylinder has spring-loaded pins that prevent the cylinder from turning until the key is placed in and moves the pins upwards to fit the height of the key in that location. This causes the cylinder eventually to rotate opening the lock body and opening the handle latch to be opened. If the door lock actuator is still not working, you can take it off it by using a small screwdriver. You will need to loosen the locking bolt first and then take off the plastic cover which holds the electrical connector. After that, disconnect the door lock actuator and let it fall. You should then be able to find the two 10mm bolts that hold the actuator in place and remove them. After the actuator has been removed, you'll be able to disconnect the black electrical connector and remove it together with the lock and actuator assembly. Replace the key Whether you have keys for your deadbolt or door knob If it's not working properly you need to either reset the lock or replace it completely. It's not hard to do this yourself and could save you lots of money. It is recommended to have a professional locksmith check the locks for any issues prior to beginning. This will give peace of assurance that your home is safe and secure. Remove the exterior faceplate of the doorknob/deadbolt. If there are screws holding the faceplate Use a screwdriver to pull it off. Then utilize a flat head screwdriver to remove the inside faceplate. After you have removed the faceplate, you can remove the bolt and screw from the lock cylinder. A locksmith can tell you whether you need to replace or rekey the lock. Repair My Windows And Doors can also offer advice on the best security measures for your home. They can also make necessary modifications to your door and frame for a perfect fit. They will also offer a warranty on their work. You will need to purchase a brand new lock key before you can reset it. It's important to use a key that fits well within the lock. A key that's not the right size can damage the internal mechanism of a lock and stop it from functioning. To test the size of a key, insert it into the lock. If the key fits completely against the plug then it's the right size. If the pins stick out from the top of the plug, they're not long. You may want to replace your door lock for a variety of reasons, including: Rekeying a lock can be an option that is less expensive than replacing one if you are moving into the home of a previous owner or if keys are missing. It can also be less costly than a full replacement. However, there are some situations in which rekeying your existing lock isn't possible. If the lock has been damaged or jammed repeatedly, for example it could be the right time to replace it.